- How To Install Ide Controller Driver For Cd Youtube Tutorial
- How To Install Ide Controller Driver For Cd Youtube Converter
- How To Install Ide Controller Driver For Cd Youtube Music
- If two devices are already in connected to the secondary IDE channel, move one of those devices to the slave position on the primary IDE controller with the hard drive. If the DVD/CD Writer must share the IDE channel with a hard drive, set the jumpers for the DVD/CD Writer drive to slave, and the leave the hard drive jumpered as master on the.
- To download, select the best match from the list below and then click the Download button. Or, you can request the driver and we will find it for you.
- How to Install AHCI Support for ATI SB600 SATA Controllers on Existing Windows Installations. SATA is the new standard for communication between a computer system and hard drives, CD and DVD drives, etc., and replaces the slower IDE.
- Computer problem? Tech Support Guy is completely free -- paid for by advertisers and donations. Click here to join today! If you're new to Tech Support Guy, we highly recommend that you visit our Guide for New Members.
Discussion in 'Earlier Versions of Windows' started by msutto, Dec 10, 2008.
Installs the driver for the ITE* IDE (PATA) controller on Intel Desktop boards for IDE CD/DVD-ROM and hard drives. Native PATA/IDE drivers in Windows* XP do not support the ITE 8211 controller. If an IDE CD/DVD-ROM or IDE hard drive is used for installation of Windows XP, the F6. Ever had trouble of installing drivers or have drivers with no setup.
- Thread Status:
- Not open for further replies.
Welcome to Tech Support Guy!
Are you looking for the solution to your computer problem? Join our site today to ask your question. This site is completely free -- paid for by advertisers and donations.
If you're not already familiar with forums, watch our Welcome Guide to get started.
over 733,556 other people just like you!
- Thread Status:
- Not open for further replies.
Short URL to this thread: https://techguy.org/778215
Buying tips and help
If you have not already purchased a CD drive, see the CD buying tips section before continuing.
How to determine the CD drive type
Before getting started
- Ensure you have a working bootable floppy diskette with CD-ROM drivers.
- Write down important information from the top or bottom of the CD-ROM such as the Model Number, Serial Number, and specifications.
- Ensure you are familiar with ESD and its potential dangers.
- When physically installing the CD drive, ensure the computer is powered down and unplugged.
Set Jumpers
Before installing the CD drive, it's important that the drive has the jumpers appropriately set to Master, Slave, or Cable Select. For example, if this drive is being attached to the same cable as your hard drive, the CD-ROM drive needs to be set to Slave and the hard drive needs to be set to Master or Dual Master.
NoteIf possible, it is recommended that if you are installing a CD-R or CD-RW drive that the drive be set up as the Master drive on the second IDE/EIDE interface. Have the drive as master can help prevent a buffer underrun when creating a CD.
Attach cables
The CD-ROM should have two cables connected to it and may have an audio cable, which is the smallest of the cables, the CD-ROM audio cable (or sound card cable). When connecting this cable to the CD-ROM drive, it should be a 3 or 4 pin cable connection (see above picture). Make sure you are connecting this cable the cable plug and not the jumpers on the back of the drive. While it may be possible for the cable to connect to these pins, this could cause additional issues.
Next, connect the 40-pin IDE/EIDE interface cable (large gray ribbon cable) to the back of the CD-ROM drive. This cable has one side of the cable that is red or blue indicating PIN 1. This side of the cable almost always points to where the power connects to the CD-ROM drive.
Finally, connect the Molex style power cable to the back of the CD-ROM drive. This cable is keyed, therefore it should only connect to the computer in one orientation.
Once the computer cables have been connected to the back of the CD-ROM drive, connect the opposite ends of the IDE/EIDE interface cable and the audio cable to their appropriate locations. The audio cable will connect to one of the following locations: sound card, motherboard (when onboard sound present), or DVD decoder card.
CMOS setup
Once the disc drive has been connected to the computer, place the case back on the computer. Connect the keyboard, monitor, and power to the computer. (We recommend that you do not connect all the cables yet. If you experience problems, you may have to disconnect all the cables again.)
How To Install Ide Controller Driver For Cd Youtube Tutorial
Once connected, turn on the computer and enter CMOS setup. Verify that the IDE device is set up as Auto or CD Drive. Once verified, save the settings and reboot the computer.
Software setup
IDE/EIDE CD-ROM drives only require the one or two CD-ROM drives for the drives to work.
If you are using MS-DOS, you need the MS-DOS driver and MSCDEX. For additional information about loading and configuring these drivers on your computer, see our CD-ROM driver page.
Hercules (Prod By Metro Boomin). Nov 13, 2015 at 12:15 AM. Update Required To play the media you will need to. Listen to and Download Hercules (Prod By Metro Boomin), the new song from Young Thug. Download This Song And More At http://DigitalDripped.com. Hercules young thug mp3 download.
If you are using Windows 9x, ME, 2000, or XP it is likely that if the drive is properly installed that it will be automatically detected and installed when the computer first boots up.
CD drivers are found on our CD-ROM, CD-R, CD-RW, and DVD drivers page.
How To Install Ide Controller Driver For Cd Youtube Converter
Troubleshooting
Additional information
How To Install Ide Controller Driver For Cd Youtube Music
- See our CD-R, CD-ROM, and DVD definitions for further information and related links.